Welcome to RVForums.com

  • Register now and join the discussion
  • Friendliest RV Community on the web
  • Modern site for PC's, Phones, Tablets - no 3rd party apps required
  • Ask questions, help others, review campgrounds
  • Get the most out of the RV Lifestyle
  • Invite everyone to RVForums.com and let's have fun
  • Commercial/Vendors welcome

Question 2004 Pace Arrow 36B bad running 8.1 Vortec

Welcome to RVForums.com

  • Register now and join the discussion
  • Modern secure site, no 3rd party apps required
  • Invite your friends and let's have fun
  • Commercial/Vendors welcome
  • Friendliest RV community on the web
The coil I bought was from AutoZone, Duralast brand ? Good or not ? I will take your advice and buy a spare, and of good quality for sure

Thanks
Not because I own a NAPA Store, but because I was a GM Service Manager for 30 + years. Autozone electronics are at the bottom of the barrel as far as quality goes. Oreilly 2nd line not much better, as well as NAPA Mileage Plus.
 
Sounds like you found the problem. My thoughts on replacing the coils is this. Many coils last well over 150000 miles without a hitch. If you are concerned buy one spare and put it in your junk drawer. Also buy a code reader so you can trouble shoot the problem code on the road. It is likely not going to be the same problem next time around. As @DHudson said, there is no saving buying cheap parts, NAPA sells quality parts, and can be found almost anywhere.

Not because I own a NAPA Store, but because I was a GM Service Manager for 30 + years. Autozone electronics are at the bottom of the barrel as far as quality goes. Oreilly 2nd line not much better, as well as NAPA

The coil I bought was from AutoZone, Duralast brand ? Good or not ? I will take your advice and buy a spare, and of good quality for sure

Thanks
Do you think it is better to buy AC Delco ? Or is NAPA just as good ?

Thanks
 
Do you think it is better to buy AC Delco ? Or is NAPA just as good ?

Thanks
AC Delco, Delphi, NAPA Echlin, Standard Ignition , NGK are all good
 
AC Delco, Delphi, NAPA Echlin, Standard Ignition , NGK are all good
I've decided to buy a scan tool, I looked at one my neighbor has and it does not have the Workhorse chasis listed on the menu, I know it's a Chevrolet 496 engine as in the trucks, but will it make a difference in the scan tool function ?

Thanks

John
 
I've decided to buy a scan tool, I looked at one my neighbor has and it does not have the Workhorse chasis listed on the menu, I know it's a Chevrolet 496 engine as in the trucks, but will it make a difference in the scan tool function ?

Thanks

John
OBD2 is fed required, it standardized the port and codes. Only special codes specific to manufactures may vary, and there are only a few, mostly to help trouble shoot. any code can be looked up online so it is not a big deal. Any OBD 2 reader will work for you,
 
OBD2 is fed required, it standardized the port and codes. Only special codes specific to manufactures may vary, and there are only a few, mostly to help trouble shoot. any code can be looked up online so it is not a big deal. Any OBD 2 reader will work for you,
Thanks for the help
 
I've decided to buy a scan tool, I looked at one my neighbor has and it does not have the Workhorse chasis listed on the menu, I know it's a Chevrolet 496 engine as in the trucks, but will it make a difference in the scan tool function ?

Thanks

John
That is basically a Chevy P3500 or P4500 chassis. It "should" work with your vehicle, but can not be sure. I would call the scan manufacture and confirm for sure.
 
I have a fuel pressure gauge hooked up while driving, yesterday we went about 70 miles for a test, no issues on the way, stopped for about 1/2 hour and started back, in about 15 miles it went into limp mode, I pulled over and shut it down and decided to try it again immediately and it started and ran fine, no wait for cool down, tried this twice on the trip home, so apparantly the cool down does nothing, just switch off and on again and the problem stops ? During the whole trip the fuel pressure was between 60 and 64 PSI. I used a scan tool when the check engine light came on and it read weak signal to 02 sensor bank 1, that's the same code we got the last three times at the shop, and they changed out the 02 sensor to no avail. Any ideas ?

Thanks

John
 
I would not rule out an intake leak. Since only 1 bank is affected, I would start there. Those are known for intake plenum gasket leaks
A code for one bank wont be a MAF sensor as the MAF feeds both banks so...
Maybe change the intake plenum gaskets first , and see if that does it.
Post the code number EXACTLY as it appears . Plenty of O2 sensor codes ,they all mean something a little different
 
Last edited:

Latest resources

Back
Top